當前位置:主頁 > 常見問題 >

正確使用橡膠接頭,提高它性能

作者:上海松夏減震器有限公司 日期:2019-01-22 來源:橡膠接頭廠家
   正確使用橡膠接頭,提高它性能
   Use rubber connector correctly to improve its performance
   第一:如果在泵出口附近或管道拐角處設計和安裝橡膠接頭,并將產品用于高壓和高層建筑懸掛,則管道必須有固定支架或固定支架。固定支架和固定支架的受力必須大于軸向力,否則產品應安裝防拔限位裝置。
   First: if rubber joints are designed and installed near the pump outlet or at the pipe corner and the product is used for high pressure and high-rise building suspension, the pipe must have a fixed support or fixed support.The force on the fixed bracket and the fixed bracket must be greater than the axial force, otherwise the product shall be installed with the anti-pulling limit device.
正確使用橡膠接頭
   第二:柔性橡膠軟接頭管結構必須處于自然狀態,安裝時不要人為地使產品變形。這樣可以避免產品的早期損壞和弱化。在安裝過程中,嚴禁使用柔性橡膠接頭進行超級位移
   Second: the structure of flexible rubber soft joint pipe must be in a natural state, do not artificially deform the product during installation.This can avoid early damage and weakening of the product.In the process of installation, it is forbidden to use flexible rubber joints for super displacement
橡膠接頭的性能
   第三:當柔性膠管接頭與管法蘭連接時,螺栓線材應延伸到管法蘭的一端,以防止螺紋受壓時橡膠軟接頭的拱被擠壓或纏繞,兩端的螺栓必須對稱緊固,以使所有螺栓的緊密性一致,使用條件差。除了增加平墊外,還應增加彈簧墊圈,以防止螺母松動。
   Third: when the flexible rubber hose joint is connected with the pipe flange, the bolt wire shall extend to one end of the pipe flange to prevent the arch of the rubber soft joint from being squeezed or wound when the thread is compressed. The bolts at both ends must be tightened symmetrically to make all the bolts have the same tightness and poor service conditions.In addition to adding flat pads, spring washers should be added to prevent the nut from loosening.
橡膠接頭生產制造商
   第四法蘭的橡膠接頭應安裝,使球體加強環的兩端全部卡在法蘭槽內,以防止球在管道承受壓力時拔出法蘭。螺栓固定時,擰緊對稱螺栓,以確保球于法蘭已就位。
   The rubber joint of the fourth flange shall be installed so that both ends of the ball reinforcing ring are all stuck in the flange groove to prevent the ball from pulling out the flange when the pipe is under pressure.When the bolt is fixed, tighten the symmetric bolt to ensure that the ball is in place on the flange.
法蘭橡膠接頭
 

橡膠接頭產品分類

  • 單球體橡膠接頭

  • 雙球體橡膠接頭

  • 同心異徑橡膠接頭

  • 偏心異徑橡膠接頭

  • 卡箍橡膠接頭

  • 螺紋絲扣橡膠接頭

  • 90度橡膠彎頭

  • 菱形法蘭橡膠接頭

  • 橡膠鴨嘴止回閥

  • ?